khubik

525 posts

khubik banner
khubik

khubik

@khubik2

I'm not the only author of Baryon Sweeper. Credits to @notzecoxao, @mathieulh, @VVildCard777, @gang_56, @RealYoti, @ErikPshat et al.

Russia Katılım Kasım 2020
43 Takip Edilen293 Takipçiler
Sabitlenmiş Tweet
khubik
khubik@khubik2·
Happy Victory Day! ⭐️ Good news: 97 and 2F keys have been found. All PSP-3000s are supported by Baryon Sweeper now. PSP Street and PSPgo are also supported. Former has no MMS image and latter has no known way to enter porttalk mode, but the keys are there!
English
10
5
21
2.8K
Jose Coixao
Jose Coixao@notnotzecoxao·
the method to enter psp go jigkick mode was finally found thanks to my brazilian wizard @leo__oliveira . he describes the method in his latest tweet. now the next challenge will be to build the necessary materials for factory service mode hardware on go.
English
1
5
73
6.7K
khubik
khubik@khubik2·
@MoradMoflih yes you do and there are no available MMS images that work with street sadly
English
1
0
1
42
morad moflih
morad moflih@MoradMoflih·
@khubik2 Oh i see k-line is on usb port, i tried to access k-line on battery connector (psp slim way) but nothing happened. I'll try what you suggested to access service mode and see if it works. But do i need an mms image to reflash the firmware ? Sorry am a total beginner. Thx khubrik
English
1
0
0
48
khubik
khubik@khubik2·
Happy Victory Day! ⭐️ Good news: 97 and 2F keys have been found. All PSP-3000s are supported by Baryon Sweeper now. PSP Street and PSPgo are also supported. Former has no MMS image and latter has no known way to enter porttalk mode, but the keys are there!
English
10
5
21
2.8K
khubik
khubik@khubik2·
@MoradMoflih psp street has some conditions to enter service mode: you have to hold down LTrigger + RTrigger + LeftDpad + Circle while flicking the power switch. has to be done from cold boot serial port (K-line) will be available on USB ID pin neither DDCv9 nor 6.20 jigkick work with street
khubik tweet media
English
1
0
1
97
khubik retweetledi
The Zett
The Zett@The_Zett·
Thanks to the recent BaryonSweeper update also supporting 04g models, it is also unbrickable and should in theory support newCIPL <3
The Zett tweet media
English
7
8
51
5.2K
khubik
khubik@khubik2·
@FiPE_ZOE no one has tested PSPgo, as no one knows how to enter service mode
English
1
0
2
161
FiPE
FiPE@FiPE_ZOE·
@khubik2 Does the leaked 6.20 MMS image work on the PSP go? Iirc the go always had a different update PBP compared to the standard PSPs🤔 But we don't need the leaked stuff anyway right? DDC could be ported to supported all models/latest FWs right?🤔
English
1
0
1
467
khubik
khubik@khubik2·
New feature: pysweeper also makes sure the jig is assembled correctly by checking for port echo.
English
0
0
8
508
khubik
khubik@khubik2·
@Fractalus9 pin 2 is required for battery authentication, PSP will not boot if it can't verify the "authenticity" of the battery
English
1
0
0
34
Fractalus
Fractalus@Fractalus9·
@khubik2 Probably OT question but: Can I connect directly any 3.6V battery to the pins 1 and 3 on PSP? Or is the pin 2 needed for anything other than charging control(I don't need charging)? Thank you.
English
1
0
0
36
khubik
khubik@khubik2·
You probably don't need a diode. I just tested with RX and TX short and it works fine
khubik tweet media
English
3
3
23
0
AG420
AG420@autismgaming420·
our great EA hater HisWattson last post of this case
AG420 tweet media
English
60
24
837
0
khubik
khubik@khubik2·
@OGXboxDev @YouTube I'm fine, I'm far from all my PSPs though. I am now studying in another city
English
1
0
1
0
khubik
khubik@khubik2·
@mrsteyk1 I know blaming management is a meme but this time its not
English
0
0
0
0
khubik
khubik@khubik2·
@mrsteyk1 Competitive players can say anything they want, but, in the end, it's the management that values their opinion over everyone else's :(
English
1
0
1
0

Keşfet

@FiPE_ZOE @notnotzecoxao @leo__oliveira @MoradMoflih @notzecoxao @The_Zett @Fractalus9 @zzattack