@gonecozycrafts @dachswerk Look up Bubble sticker gun.
English
Azzys Design Works
25.9K posts
Azzys Design Works
@AzzyDesignWorks
Azzy runs a small design shop in Pennsylvania, loves jeeps, fast cars and personal liberty. All taxes suck. Follows =/= endorsements. DMs open to real humans.
Finleyville PA Beigetreten Şubat 2013
780 Folgt1.2K Follower
@dachswerk Thanks. I'm trying to make a European version of a certain keychain manufacturer from overseas so I need it to be perfect. Clear resin will need a lot of time and effort sadly
English
Like printing on one side, and then encapsulating it? Other than a triple (or more) embossing clear passes, no. I would suggest running a second UV pass on any embossing unless you like fingerprints though.
Anything that can glue the plastic together like solvent is also going to attack the print.
English
@DIYMaker_Johan @Windows @satyanadella Big files, use TeraCopy. much more efficient than Windows built in transfer.
English
Really need to go to Linux.... Stupid @Windows 11. You @satyanadella ruined it with current #microslop.
Transfers from disk to another, yes all SSD, takes so long nowadays. Often minutes of tranfers sitting on 0 bytes/s, then moving in, then again on 0 for a while. 😮💨💀
English
@xiphmont printables.com/model/909107-c…
I would use the built in pressure advance tool in prusaslicer
GIF
English
@devmobnow Pressure advance. It just advanced the wrong way.
English
@binarycrystal @joeltelling Just checked, Current FW. I had the RC, until they updated to 6.4.0 for One+
English
@AzzyDesignWorks @joeltelling Yeah, I've found I can get pretty good top surfaces using tuned flow and single perimeter. Although ASA and PETG-CF are the most "exotic" things I've used so I definitely have plenty to learn.
English
@AzzyDesignWorks Oooh, that's a test print with some hand-rolled gcode right? I have some pretty strong bets.
Got a URL? :-)
English
I only noticed it with this material (CarbonX PA6GF) and it sounds like its trying to retract on wipe at warp speed. Which I wonder if thats due to the silly long ptfe tube to the drybox and pressure in that line. I'll need to tune it.
Thanks for the heads up on that setting. I usually have it going during nylon to get better top surfaces.
English
@AzzyDesignWorks @joeltelling I could be wrong, but everything I've found points to some firmware bug with that setting for Prusa printers.
Interesting bad, or just unique? My C1+ kit isn't silent, but so far I'm aware of all the "regular" noises mine makes and just live with it.
English
@joeltelling Hmmm.. What did you change? Maybe they were bragging. 😂
English
@AzzyDesignWorks I had a layer shift on my C1 today as well, did our machines talk?
English
@binarycrystal @joeltelling Yes. AndbI have to check acceleration settings, because the wipe makes an interesting noise.
English
@joeltelling @AzzyDesignWorks Are you using "Avoid crossing perimeters"?
Every single time I have it checked, I get layer shifts, without it, perfect.
English
@M1chl First time I've had it for no reason. I'll check it out, I don't go looking for firmware unless something's wrong.
English
@AzzyDesignWorks Do you have latest RC firmware? Because they solved issues with layer shifting, I did not have any layer shift since.
English
@andrewkornuta Less spending overall, but a lot of Amazon re-labelers are gone from the platform, which would give these guys lower sales too.
With the added side that their race to the bottom prices and quality to match is seen by the general public.
English
@digitaldragon72 If its not extrusion based, and the issue is consistent throughout, are the belts tensioned right, and does it make any noise from a bad bearing when moving?
English
The FlashForge Dreamer has two extruders and hotends mounted side by side. They use plastic housings/levers for the extruder. A single Hobbes gear directly mounted to the motor shaft. I took both apart and checked for clogs and expected to find the dreaded cracked tension arm at the shoulder bolt. Neither extruder was cracked.
What would you recommend next?
English
I have a conflict tonight and will not be streaming. I will leave you all with a puzzle. A FlashForge Dreamer came into the shop with the following issue. "All prints look like fuzzy skin is on."
What are your suggestions to check?
English
@thereal_SnS @USAA We have been priced out of using anyone else, and Im concerned. This explains the issues we had joining and with billing.
English
Now I know why @usaa essentially ignored our claim after Hurricane Helene for almost a year, and still hasn’t worked to settle our case.
Matt Forney@mattforney
EXCLUSIVE: an insider at USAA provides footage of the company's recent Diwali event. It looks like a Tim and Eric skit. Remember, while USAA throws parties for Indians, it ignores American holidays and its veteran employees are committing suicide from stress and layoffs.
English
Id like to add, that while doing tuning on the C1, its fed perfectly.
Also, tuning filament is a giant PITA in @PrusaSlicer. Its either find a file where someone has done the work and tweaked a 3mf on printables (and probably not for your exact setup), or guess. The calibration menu in Orca works so much better.
English
@synblinkerfluid Oshkosh seems to be the Keltec of vehicles.
English
Fairly certain the postal employees felt the same from the transition from the Jeep DJ to the Grumman LLV.
ThePOTSPostman@ThePOTSPostman
I can’t believe I have to drive this thing around town soon. The new mail trucks are hideous. Looks like a platypus.
English